[CCNAv6 S1] 8.3.1.4 Packet Tracer - Implementing a Subnetted IPv6 Addressing Scheme



Packet Tracer - Implementing a Subnetted IPv6 Addressing Scheme
Addressing Table

Objectives

Part 1: Determine the IPv6 Subnets and Addressing Scheme

Part 2: Configure the IPv6 Addressing on Routers and PCs and Verify Connectivity

Scenario

Your network administrator wants you to assign five /64 IPv6 subnets to the network shown in the topology. Your job is to determine the IPv6 subnets, assign IPv6 addresses to the routers, and set the PCs to automatically receive IPv6 addressing. Your final step is to verify connectivity between IPv6 hosts.

Part 1:     Determine the IPv6 Subnets and Addressing Scheme
Step 1:     Determine the number of subnets needed.

Start with the IPv6 subnet 2001:DB8:ACAD:00C8::/64 and assign it to the R1 LAN attached to GigabitEthernet 0/0, as shown in the Subnet Table. For the rest of the IPv6 subnets, increment the 2001:DB8:ACAD:00C8::/64 subnet address by 1 and complete the Subnet Table with the IPv6 subnet addresses.


Step 2:     Assign IPv6 addressing to the routers.

a.     Assign the first IPv6 addresses to R1 for the two LAN links and the WAN link.

b.    Assign the first IPv6 addresses to R2 for the two LANs. Assign the second IPv6 address for the WAN link.

c.     Document the IPv6 addressing scheme in the Addressing Table.

Part 2:     Configure the IPv6 Addressing on Routers and PCs and Verify Connectivity
Step 1:     Configure the routers with IPv6 addressing.

Note: This network is already configured with some IPv6 commands that are covered in a later course. At this point in your studies, you only need to know how to configure IPv6 address on an interface.

Configure R1 and R2 with the IPv6 addresses you specified in the Addressing Table and activate the interfaces.

Router(config-if)# ipv6 address ipv6-address/prefix
Router(config-if)# ipv6 address ipv6-link-local link-local
Step 2:     Configure the PCs to automatically receive IPv6 addressing.

Configure the four PCs for autoconfiguration. Each should then automatically receive full IPv6 addresses from the routers.

Step 3:     Verify connectivity between the PCs.

Each PC should be able to ping the other PCs and the routers.

Suggested Scoring Rubric





Configuration R1: 

enable
configure terminal
interface g0/0
 ipv6 address 2001:DB8:ACAD:00C8::1/64
 ipv6 address FE80::1 link-local
 no shutdown
interface g0/1
 ipv6 address 2001:DB8:ACAD:00C9::1/64
 ipv6 address FE80::1 link-local
 no shutdown
interface s0/0/0
 ipv6 address 2001:DB8:ACAD:00CA::1/64
 ipv6 address FE80::1 link-local
 no shutdown
 exit
!
Configuration R2: 

enable
configure terminal
interface g0/0
 ipv6 address 2001:DB8:ACAD:00CA::1/64
 ipv6 address FE80::2 link-local
 no shutdown
interface g0/1
 ipv6 address 2001:DB8:ACAD:00CB::1/64
 ipv6 address FE80::2 link-local
 no shutdown
interface s0/0/0
 ipv6 address 2001:DB8:ACAD:00CC::1/64
 ipv6 address FE80::2 link-local
 no shutdown
 exit
!
Configuration PC1:



 Configuration PC2:


Configuration PC3: 


Configuration PC4: 




Link Download: Here


Nhận xét

Đăng nhận xét

Bài đăng phổ biến từ blog này

[CCNAv6 S4] 8.2.4.14 Packet Tracer - Troubleshooting Enterprise Networks 3

Hình ảnh
Packet Tracer – Troubleshooting Enterprise Networks 3 Addressing Table Background This activity uses a variety of technologies you have encountered during your CCNA studies, including routing, port security, EtherChannel, DHCP, NAT, PPP, and Frame Relay. Your task is to review the requirements, isolate and resolve any issues, and then document the steps you took to verify the requirements. Note: This activity begins with a partial score. Requirements DHCP ·         R1 is the DHCP server for the R1 LAN. Switching Technologies ·         Port security is configured to only allow PC1 to access S1's F0/3 interface. All violations should disable the interface. ·         Link aggregation using EtherChannel is configured on S2, S3, and S4. Routing ·         All routers are configured with OSPF process ID 1 and no routing updates should be sent across interfaces that do n...
Đọc thêm

[CCNAv6 S2] 2.2.2.4 Packet Tracer - Configuring IPv4 Static and Default Routes

Hình ảnh
Packet Tracer - Configuring IPv4 Static and Default Routes Addressing Table Objectives Part 1: Examine the Network and Evaluate the Need for Static Routing Part 2: Configure Static and Default Routes Part 3: Verify Connectivity Background In this activity, you will configure static and default routes. A static route is a route that is entered manually by the network administrator to create a reliable and safe route. There are four different static routes that are used in this activity: a recursive static route, a directly attached static route, a fully specified static route, and a default route. Part 1:     Examine the Network and Evaluate the Need for Static Routing a.     Looking at the topology diagram, how many networks are there in total? b.    How many networks are directly connected to R1, R2, and R3? c.     How many static routes are required by each router to reach networks that are not directly ...
Đọc thêm

[CCNAv6 S2] 7.3.2.4 Packet Tracer - Troubleshooting Standard IPv4 ACLs

Hình ảnh
Packet Tracer – Troubleshooting Standard IPv4 ACLs Addressing Table Objectives Part 1: Troubleshoot ACL Issue 1 Part 2: Troubleshoot ACL Issue 2 Part 3: Troubleshoot ACL Issue 3 Scenario This network is meant to have the following three policies implemented: ·         Hosts from the 192.168.0.0/24 network are unable to access network 10.0.0.0/8. ·         L3 can’t access any devices in network 192.168.0.0/24. ·         L3 can’t access Server1 or Server2. L3 should only access Server3. ·         Hosts from the 172.16.0.0/16 network have full access to Server1, Server2 and Server3. Note: All FTP usernames and passwords are “cisco”. No other restrictions should be in place. Unfortunately, the rules that have been implemented are not working correctly. Your task is to find and fix the errors related to the access lists on R1. Part 1:     Troublesh...
Đọc thêm