[CCNAv6 S3] 6.4.3.4 Packet Tracer - Configuring Basic EIGRP with IPv6 Routing




Packet Tracer – Configuring Basic EIGRP with IPv6
Addressing Table



Objectives

Part 1: Configure EIGRP for IPv6 Routing

Part 2: Verify IPv6 EIGRP for IPv6 Routing

Scenario

In this activity, you will configure the network with EIGRP routing for IPv6. You will also assign router IDs, configure passive interfaces, verify the network is fully converged, and display routing information using show commands.

EIGRP for IPv6 has the same overall operation and features as EIGRP for IPv4. There are a few major differences between them:

·         EIGRP for IPv6 is configured directly on the router interfaces.
·         With EIGRP for IPv6, a router-id is required on each router or the routing process will not start.
·         The EIGRP for IPv6 routing process uses a “shutdown” feature.
Part 1:     Configure EIGRP for IPv6 Routing
Step 1:     Enable IPv6 routing on each router.

Step 2:     Enable EIGRP for IPv6 routing on each router.

The IPv6 routing process is shutdown by default. Issue a command that will enable EIGRP for IPv6 routing in R1, R2 and R3.

Enable the EIGRP process on all routers and use 1 as the Autonomous System number.

Step 3:     Assign a router ID to each router.

The router IDs are as follows:
·         R1: 1.1.1.1
·         R2: 2.2.2.2
·         R3: 3.3.3.3
Step 4:     Using AS 1, configure EIGRP for IPv6 on each interface.

Part 2:     Verify EIGRP for IPv6 Routing
Step 1:     Examine neighbor adjacencies.

Use the command show ipv6 eigrp neighbors to verify that the adjacency has been established with its neighboring routers. The link-local addresses of the neighboring routers are displayed in the adjacency table.

Step 2:     Examine the IPv6 EIGRP routing table.

Use the show ipv6 route command to display the IPv6 routing table on all routers. EIGRP for IPv6 routes are denoted in the routing table with a D.

Step 3:     Verify the parameters and current state of the active IPv6 routing protocol processes.

Use the command show ipv6 protocols to verify the configured parameter.

Step 4:     Verify end-to-end connectivity.

PC1, PC2, and PC3 should now be able to ping each other. If not, troubleshoot your EIGRP configurations.




Configuration R1:

enable
configure terminal
ipv6 unicast-routing
ipv6 router eigrp 1
 no shutdown
 eigrp router-id 1.1.1.1
 exit
interface g0/0
 ipv6 eigrp 1
interface s0/0/0
 ipv6 eigrp 1
interface s0/0/1
 ipv6 eigrp 1
 end
write memory
!

Configuration R2:

enable
configure terminal
ipv6 unicast-routing
ipv6 router eigrp 1
 no shutdown
 eigrp router-id 2.2.2.2
 exit
interface g0/0
 ipv6 eigrp 1
interface s0/0/0
 ipv6 eigrp 1
interface s0/0/1
 ipv6 eigrp 1
 end
write memory
!

Configuration R3:

enable
configure terminal
ipv6 unicast-routing
ipv6 router eigrp 1
 no shutdown
 eigrp router-id 3.3.3.3
 exit
interface g0/0
 ipv6 eigrp 1
interface s0/0/0
 ipv6 eigrp 1
interface s0/0/1
 ipv6 eigrp 1
 end
write memory
!

END !~!


Nhận xét

Đăng nhận xét

Bài đăng phổ biến từ blog này

[CCNAv6 S2] 2.2.2.4 Packet Tracer - Configuring IPv4 Static and Default Routes

Hình ảnh
Packet Tracer - Configuring IPv4 Static and Default Routes Addressing Table Objectives Part 1: Examine the Network and Evaluate the Need for Static Routing Part 2: Configure Static and Default Routes Part 3: Verify Connectivity Background In this activity, you will configure static and default routes. A static route is a route that is entered manually by the network administrator to create a reliable and safe route. There are four different static routes that are used in this activity: a recursive static route, a directly attached static route, a fully specified static route, and a default route. Part 1:     Examine the Network and Evaluate the Need for Static Routing a.     Looking at the topology diagram, how many networks are there in total? b.    How many networks are directly connected to R1, R2, and R3? c.     How many static routes are required by each router to reach networks that are not directly ...
Đọc thêm

[CCNAv6 S2] 8.3.1.2 Packet Tracer - Skills Integration Challenge

Hình ảnh
Packet Tracer – Skills Integration Challenge Addressing Table VLAN Port Assignments and DHCP Information Scenario In this culminating activity, you will configure VLANs, trunks, DHCP Server, DHCP relay agents, and configure a router as a DHCP client. Requirements Using the information in the tables above, implement the following requirements: ·         Create VLANs on S2 and assign VLANs to appropriate ports. Names are case-sensitive ·         Configure S2 ports for trunking. ·         Configure all non-trunk ports on S2 as access ports. ·         Configure R1 to route between VLANs. Subinterface names should match the VLAN number. ·         Configure R1 to act as a DHCP server for the VLANs attached to S2. -       Create a DHCP pool for each VLAN. Names are case-sensitive. -       Assign the ap...
Đọc thêm

[CCNAv6 S2] 9.4.1.2 Packet Tracer - Skills Integration Challenge Part II

Hình ảnh
Packet Tracer – Skills Integration Challenge Addressing Table VLANs and Port Assignments Table Scenario This culminating activity includes many of the skills that you have acquired during this course. First, you will complete the documentation for the network. So make sure you have a printed version of the instructions. During implementation, you will configure VLANs, trunking, port security and SSH remote access on a switch. Then, you will implement inter-VLAN routing and NAT on a router. Finally, you will use your documentation to verify your implementation by testing end-to-end connectivity. Documentation You are required to fully document the network. You will need a print out of this instruction set, which will include an unlabeled topology diagram: -       Label all the device names, network addresses and other important information that Packet Tracer generated. -       Complete the Addressing Table and VLANs and Por...
Đọc thêm