[CCNAv6 S4] 3.4.2.4 Packet Tracer - Configuring GRE



Packet Tracer – Configuring GRE
Addressing Table


Objectives

Part 1: Verify Router Connectivity

Part 2: Configure GRE Tunnels

Part 3: Verify PC Connectivity

Scenario

You are the network administrator for a company which wants to set up a GRE tunnel to a remote office. Both networks are locally configured, and need only the tunnel configured.

Part 1:     Verify Router Connectivity
Step 1:     Ping RA from RB.

a.     Use the show ip interface brief command on RA to determine the IP address of the S0/0/0 port.

b.    From RB ping the IP S0/0/0 address of RA.

Step 2:     Ping PCA from PCB.

Attempt to ping the IP address of PCA from PCB. We will repeat this test after configuring the GRE tunnel. What were the ping results? Why?

Part 2:     Configure GRE Tunnels
Step 1:     Configure the Tunnel 0 interface of RA.

a.     Enter into the configuration mode for RA Tunnel 0.

RA(config)# interface tunnel 0
b.    Set the IP address as indicated in the Addressing Table.

RA(config-if)# ip address 10.10.10.1 255.255.255.252
c.     Set the source and destination for the endpoints of Tunnel 0.

RA(config-if)# tunnel source s0/0/0
RA(config-if)# tunnel destination 209.165.122.2
d.    Configure Tunnel 0 to convey IP traffic over GRE.

RA(config-if)# tunnel mode gre ip
e.     The Tunnel 0 interface should already be active. In the event that it is not, treat it like any other interface.

RA(config-if)# no shutdown
Step 2:     Configure the Tunnel 0 interface of RB.

Repeat Steps 1a – e with RB. Be sure to change the IP addressing as appropriate.

Step 3:     Configure a route for private IP traffic.

Establish a route between the 192.168.X.X networks using the 10.10.10.0/30 network as the destination.

RA(config)# ip route 192.168.2.0 255.255.255.0 10.10.10.2
RB(config)# ip route 192.168.1.0 255.255.255.0 10.10.10.1
Part 3:     Verify Router Connectivity
Step 1:     Ping PCA from PCB.

Attempt to ping the IP address of PCA from PCB. The ping should be successful.

Step 2:     Trace the path from PCA to PCB.

Attempt to trace the path from PCA to PCB. Note the lack of public IP addresses in the output.



Configuration RA:

enable
configure terminal
interface tunnel 0
 ip address 10.10.10.1 255.255.255.252
 tunnel source s0/0/0
 tunnel destination 209.165.122.2
 tunnel mode gre ip
 no shutdown
 exit
ip route 192.168.2.0 255.255.255.0 10.10.10.2
end
write memory
!


Configuration RB:

enable
configure terminal
interface tunnel 0
 ip address 10.10.10.2 255.255.255.252
 tunnel source s0/0/0
 tunnel destination 64.103.211.2
 tunnel mode gre ip
 no shutdown
 exit
ip route 192.168.1.0 255.255.255.0 10.10.10.1
end
write memory
!

END !~!


Nhận xét

Đăng nhận xét

Bài đăng phổ biến từ blog này

[CCNAv6 S4] 8.2.4.14 Packet Tracer - Troubleshooting Enterprise Networks 3

Hình ảnh
Packet Tracer – Troubleshooting Enterprise Networks 3 Addressing Table Background This activity uses a variety of technologies you have encountered during your CCNA studies, including routing, port security, EtherChannel, DHCP, NAT, PPP, and Frame Relay. Your task is to review the requirements, isolate and resolve any issues, and then document the steps you took to verify the requirements. Note: This activity begins with a partial score. Requirements DHCP ·         R1 is the DHCP server for the R1 LAN. Switching Technologies ·         Port security is configured to only allow PC1 to access S1's F0/3 interface. All violations should disable the interface. ·         Link aggregation using EtherChannel is configured on S2, S3, and S4. Routing ·         All routers are configured with OSPF process ID 1 and no routing updates should be sent across interfaces that do n...
Đọc thêm

[CCNAv6 S2] 2.2.2.4 Packet Tracer - Configuring IPv4 Static and Default Routes

Hình ảnh
Packet Tracer - Configuring IPv4 Static and Default Routes Addressing Table Objectives Part 1: Examine the Network and Evaluate the Need for Static Routing Part 2: Configure Static and Default Routes Part 3: Verify Connectivity Background In this activity, you will configure static and default routes. A static route is a route that is entered manually by the network administrator to create a reliable and safe route. There are four different static routes that are used in this activity: a recursive static route, a directly attached static route, a fully specified static route, and a default route. Part 1:     Examine the Network and Evaluate the Need for Static Routing a.     Looking at the topology diagram, how many networks are there in total? b.    How many networks are directly connected to R1, R2, and R3? c.     How many static routes are required by each router to reach networks that are not directly ...
Đọc thêm

[CCNAv6 S2] 7.3.2.4 Packet Tracer - Troubleshooting Standard IPv4 ACLs

Hình ảnh
Packet Tracer – Troubleshooting Standard IPv4 ACLs Addressing Table Objectives Part 1: Troubleshoot ACL Issue 1 Part 2: Troubleshoot ACL Issue 2 Part 3: Troubleshoot ACL Issue 3 Scenario This network is meant to have the following three policies implemented: ·         Hosts from the 192.168.0.0/24 network are unable to access network 10.0.0.0/8. ·         L3 can’t access any devices in network 192.168.0.0/24. ·         L3 can’t access Server1 or Server2. L3 should only access Server3. ·         Hosts from the 172.16.0.0/16 network have full access to Server1, Server2 and Server3. Note: All FTP usernames and passwords are “cisco”. No other restrictions should be in place. Unfortunately, the rules that have been implemented are not working correctly. Your task is to find and fix the errors related to the access lists on R1. Part 1:     Troublesh...
Đọc thêm