[CCNAv6 S4] 8.2.4.13 Packet Tracer - Troubleshooting Enterprise Networks 2



Packet Tracer – Troubleshooting Enterprise Networks 2
Addressing Table


Background

This activity uses IPv6 configurations that include DHCPv6, EIGRPv6, and IPv6 default routing. Your task is to review the requirements, isolate and resolve any issues, and then document the steps you took to verify the requirements.
Requirements

DHCPv6

·         Host_A and Host_B are assigned through IPv6 DHCP configured on R1.
IPv6 Routing

·         Each router is configured with IPv6 EIGRP and uses AS 100.
·         R3 is advertising a summary route to R2 and R1 for the two R3 LANs.
·         R2 is configured with a fully specified default route pointing to the ISP.
Connectivity

·         Devices should be configured according to the Addressing Table.
·         Every device should be able to ping every other device.
Troubleshooting Documentation

Verification Documentation

Capture output from verification commands and provide documentation proving that each of the requirements has been satisfied.

Note: Some EIGRPv6 commands are not scored in Packet Tracer v6.0.1. Your instructor will verify that all requirements are met.



Suggested Scoring Rubric

Packet Tracer scores 50 points. The troubleshooting documentation and instructor verification is worth 50 points.




Configuration R1:

enable
configure terminal
interface s0/0/1
 ipv6 address 2001:DB8:ACAD:31::1/64
 end
write memory
!

Configuration  R2:

enable
configure terminal
interface g0/0
 no ipv6 eigrp 1000
 ipv6 eigrp 100
 exit
!
no ipv6 route ::/0 GigabitEthernet0/0 2001:DB8:ACAD:F::
ipv6 route ::/0 GigabitEthernet0/1 2001:DB8:ACAD:F::1
end
write memory
!
Configuration R3:

enable
configure terminal
no ipv6 router eigrp 1000
ipv6 router eigrp 100
 no shutdown
 end
write memory
!


Nhận xét

Đăng nhận xét

Bài đăng phổ biến từ blog này

[CCNAv6 S4] 8.2.4.14 Packet Tracer - Troubleshooting Enterprise Networks 3

Hình ảnh
Packet Tracer – Troubleshooting Enterprise Networks 3 Addressing Table Background This activity uses a variety of technologies you have encountered during your CCNA studies, including routing, port security, EtherChannel, DHCP, NAT, PPP, and Frame Relay. Your task is to review the requirements, isolate and resolve any issues, and then document the steps you took to verify the requirements. Note: This activity begins with a partial score. Requirements DHCP ·         R1 is the DHCP server for the R1 LAN. Switching Technologies ·         Port security is configured to only allow PC1 to access S1's F0/3 interface. All violations should disable the interface. ·         Link aggregation using EtherChannel is configured on S2, S3, and S4. Routing ·         All routers are configured with OSPF process ID 1 and no routing updates should be sent across interfaces that do n...
Đọc thêm

[CCNAv6 S2] 2.2.2.4 Packet Tracer - Configuring IPv4 Static and Default Routes

Hình ảnh
Packet Tracer - Configuring IPv4 Static and Default Routes Addressing Table Objectives Part 1: Examine the Network and Evaluate the Need for Static Routing Part 2: Configure Static and Default Routes Part 3: Verify Connectivity Background In this activity, you will configure static and default routes. A static route is a route that is entered manually by the network administrator to create a reliable and safe route. There are four different static routes that are used in this activity: a recursive static route, a directly attached static route, a fully specified static route, and a default route. Part 1:     Examine the Network and Evaluate the Need for Static Routing a.     Looking at the topology diagram, how many networks are there in total? b.    How many networks are directly connected to R1, R2, and R3? c.     How many static routes are required by each router to reach networks that are not directly ...
Đọc thêm

[CCNAv6 S2] 7.3.2.4 Packet Tracer - Troubleshooting Standard IPv4 ACLs

Hình ảnh
Packet Tracer – Troubleshooting Standard IPv4 ACLs Addressing Table Objectives Part 1: Troubleshoot ACL Issue 1 Part 2: Troubleshoot ACL Issue 2 Part 3: Troubleshoot ACL Issue 3 Scenario This network is meant to have the following three policies implemented: ·         Hosts from the 192.168.0.0/24 network are unable to access network 10.0.0.0/8. ·         L3 can’t access any devices in network 192.168.0.0/24. ·         L3 can’t access Server1 or Server2. L3 should only access Server3. ·         Hosts from the 172.16.0.0/16 network have full access to Server1, Server2 and Server3. Note: All FTP usernames and passwords are “cisco”. No other restrictions should be in place. Unfortunately, the rules that have been implemented are not working correctly. Your task is to find and fix the errors related to the access lists on R1. Part 1:     Troublesh...
Đọc thêm