[CCNAv6 S1] 7.2.4.9 Packet Tracer - Configuring IPv6 Addressing



Packet Tracer - Configuring IPv6 Addressing
Addressing Table


Objectives

Part 1: Configure IPv6 Addressing on the Router

Part 2: Configure IPv6 Addressing on Servers

Part 3: Configure IPv6 Addressing on Clients

Part 4: Test and Verify Network Connectivity

Background

In this activity, you will practice configuring IPv6 addresses on a router, servers, and clients. You will also practice verifying your IPv6 addressing implementation.

Part 1:     Configure IPv6 Addressing on the Router
Step 1:     Enable the router to forward IPv6 packets.

a.     Enter the ipv6 unicast-routing global configuration command. This command must be configured to enable the router to forward IPv6 packets. This command will be discussed in a later semester.

R1(config)# ipv6 unicast-routing
Step 2:     Configure IPv6 addressing on GigabitEthernet0/0.

a.     Click R1 and then the CLI tab. Press Enter.

b.    Enter privileged EXEC mode.

c.     Enter the commands necessary to transition to interface configuration mode for GigabitEthernet0/0.

d.    Configure the IPv6 address with the following command:

R1(config-if)# ipv6 address 2001:DB8:1:1::1/64
e.     Configure the link-local IPv6 address with the following command:

R1(config-if)# ipv6 address FE80::1 link-local
f.     Activate the interface.

Step 3:     Configure IPv6 addressing on GigabitEthernet0/1.

a.     Enter the commands necessary to transition to interface configuration mode for GigabitEthernet0/1.

b.    Refer to the Addressing Table to obtain the correct IPv6 address.

c.     Configure the IPv6 address, the link-local address and activate the interface.

Step 4:     Configure IPv6 addressing on Serial0/0/0.

a.     Enter the commands necessary to transition to interface configuration mode for Serial0/0/0.

b.    Refer to the Addressing Table to obtain the correct IPv6 address.

c.     Configure the IPv6 address, the link-local and activate the interface.

Part 2:     Configure IPv6 Addressing on the Servers
Step 1:     Configure IPv6 addressing on the Accounting Server.

a.     Click Accounting and click the Desktop tab > IP Configuration.

b.    Set the IPv6 Address to 2001:DB8:1:1::4 with a prefix of /64.

c.     Set the IPv6 Gateway to the link-local address, FE80::1.

Step 2:     Configure IPv6 addressing on the CAD Server.

Repeat Steps 1a to 1c for the CAD server. Refer to the Addressing Table for the IPv6 address.

Part 3:     Configure IPv6 Addressing on the Clients
Step 1:     Configure IPv6 addressing on the Sales and Billing Clients.

a.     Click Billing and then select the Desktop tab followed by IP Configuration.

b.    Set the IPv6 Address to 2001:DB8:1:1::3 with a prefix of /64.

c.     Set the IPv6 Gateway to the link-local address, FE80::1.

d.    Repeat Steps 1a through 1c for Sales. Refer to the Addressing Table for the IPv6 address.

Step 2:     Configure IPv6 Addressing on the Engineering and Design Clients.

a.     Click Engineering and then select the Desktop tab followed by IP Configuration.

b.    Set the IPv6 Address to 2001:DB8:1:2::3 with a prefix of /64.

c.     Set the IPv6 Gateway to the link-local address, FE80::1.

d.    Repeat Steps 1a through 1c for Design. Refer to the Addressing Table for the IPv6 address.

Part 4:     Test and Verify Network Connectivity
Step 1:     Open the server web pages from the clients.

a.     Click Sales and click the Desktop tab. Close the IP Configuration window, if necessary.

b.    Click Web Browser. Enter 2001:DB8:1:1::4 in the URL box and click Go. The Accounting website should appear.

c.     Enter 2001:DB8:1:2::4 in the URL box and click Go. The CAD website should appear.

d.    Repeat steps 1a through 1d for the rest of the clients.

Step 2:     Ping the ISP.

a.     Open any client computer configuration window by clicking the icon.

b.    Click the Desktop tab > Command Prompt.

c.     Test connectivity to the ISP by entering the following command:

PC> ping 2001:DB8:1:A001::1
d.    Repeat the ping command with other clients until full connectivity is verified.


Configuration R1:


enable
configure terminal
ipv6 unicast-routing
!
interface g0/0
 ipv6 address 2001:DB8:1:1::1/64
 ipv6 address FE80::1 link-local
 no shutdown
!
interface g0/1
 ipv6 address 2001:DB8:1:2::1/64
 ipv6 address FE80::1 link-local
 no shutdown
!
interface s0/0/0
 ipv6 address 2001:DB8:1:A001::2/64
 ipv6 address FE80::1 link-local
 no shutdown
!


Configuration Sales:


Configuration Billing:


Configuration Accounting:


Configuration Design:


Configuration Engineering:


Configuration CAD:




Verify web: 





Link Download: Here

Nhận xét

Đăng nhận xét

Bài đăng phổ biến từ blog này

[CCNAv6 S2] 2.2.2.4 Packet Tracer - Configuring IPv4 Static and Default Routes

Hình ảnh
Packet Tracer - Configuring IPv4 Static and Default Routes Addressing Table Objectives Part 1: Examine the Network and Evaluate the Need for Static Routing Part 2: Configure Static and Default Routes Part 3: Verify Connectivity Background In this activity, you will configure static and default routes. A static route is a route that is entered manually by the network administrator to create a reliable and safe route. There are four different static routes that are used in this activity: a recursive static route, a directly attached static route, a fully specified static route, and a default route. Part 1:     Examine the Network and Evaluate the Need for Static Routing a.     Looking at the topology diagram, how many networks are there in total? b.    How many networks are directly connected to R1, R2, and R3? c.     How many static routes are required by each router to reach networks that are not directly ...
Đọc thêm

[CCNAv6 S2] 8.3.1.2 Packet Tracer - Skills Integration Challenge

Hình ảnh
Packet Tracer – Skills Integration Challenge Addressing Table VLAN Port Assignments and DHCP Information Scenario In this culminating activity, you will configure VLANs, trunks, DHCP Server, DHCP relay agents, and configure a router as a DHCP client. Requirements Using the information in the tables above, implement the following requirements: ·         Create VLANs on S2 and assign VLANs to appropriate ports. Names are case-sensitive ·         Configure S2 ports for trunking. ·         Configure all non-trunk ports on S2 as access ports. ·         Configure R1 to route between VLANs. Subinterface names should match the VLAN number. ·         Configure R1 to act as a DHCP server for the VLANs attached to S2. -       Create a DHCP pool for each VLAN. Names are case-sensitive. -       Assign the ap...
Đọc thêm

[CCNAv6 S3] 7.2.3.5 Packet Tracer - Troubleshooting EIGRP for IPv4

Hình ảnh
Packet Tracer – Troubleshooting EIGRP for IPv4 Addressing Table Scenario In this activity, you will troubleshoot EIGRP neighbor issues. Use show commands to identify errors in the network configuration. Then, you will document the errors you discover and implement an appropriate solution. Finally, you will verify full end-to-end connectivity is restored. Troubleshooting Process 1.     Use testing commands to discover connectivity problems in the network and document the problem in the Documentation Table. 2.     Use verification commands to discover the source of the problem and devise an appropriate solution to implement. Document the proposed solution in the Documentation Table. 3.     Implement each solution one at a time and verify if the problem is resolved. Indicate the resolution status in the Documentation Table. 4.     If the problem is not resolved, it may be necessary to first remove the implemented solution befor...
Đọc thêm