[CCNAv6 S1] 11.2.4.5 Packet Tracer - Configuring Secure Passwords and SSH



Packet Tracer – Configuring Secure Passwords and SSH
Addressing Table


The network administrator has asked you to prepare RTA for deployment. Before it can be connected to the network, security measures must be enabled.

Requirements

·         Configure IP addressing on PCA according to the Addressing Table.
·         Console into RTA from the Terminal on PC-A.
·         Configure IP addressing on RTA and enable the interface.
·         Configure the hostname as RTA.
·         Encrypt all plaintext passwords.
RTA(config)# service password-encryption
·         Set a strong secret password of your choosing.
·         Set the domain name to RTA.com (case-sensitive for scoring in PT).
RTA(config)# ip domain-name RTA.com
·         Create a user of your choosing with a strong password.
RTA(config)# username any_user password any_password
·         Generate 1024-bit RSA keys.
Note: In Packet Tracer, enter the crypto key generate rsa command and press Enter to continue.
RTA(config)# crypto key generate rsa
·         Block anyone for three minutes who fails to log in after four attempts within a two-minute period.
RTA(config)# login block-for 180 attempts 4 within 120
·         Configure the VTY lines for SSH access and use the local user profiles for authentication.
RTA(config)# line vty 0 4
RTA(config-line)# transport input ssh
RTA(config-line)# login local
·         Save the configuration to NVRAM.
·         Be prepared to demonstrate to your instructor that you have established SSH access from PCA to RTA.

Isomorph ID: 12

Configuration RTA:




enable
configure terminal
interface g0/0
 ip address 172.16.31.1 255.255.255.0
 no shutdown
 exit
hostname RTA
service password-encryption
enable secret Cis&o12345
ip domain-name RTA.com
username admin password CiscoCCNA
crypto key generate rsa
1024

login block-for 180 attempts 4 within 120
line vty 0 4
 transport input ssh
 login local
 end
write memory
!

Configuration PC-A:




Link Download: Here


Nhận xét

Đăng nhận xét

Bài đăng phổ biến từ blog này

[CCNAv6 S2] 2.2.2.4 Packet Tracer - Configuring IPv4 Static and Default Routes

Hình ảnh
Packet Tracer - Configuring IPv4 Static and Default Routes Addressing Table Objectives Part 1: Examine the Network and Evaluate the Need for Static Routing Part 2: Configure Static and Default Routes Part 3: Verify Connectivity Background In this activity, you will configure static and default routes. A static route is a route that is entered manually by the network administrator to create a reliable and safe route. There are four different static routes that are used in this activity: a recursive static route, a directly attached static route, a fully specified static route, and a default route. Part 1:     Examine the Network and Evaluate the Need for Static Routing a.     Looking at the topology diagram, how many networks are there in total? b.    How many networks are directly connected to R1, R2, and R3? c.     How many static routes are required by each router to reach networks that are not directly ...
Đọc thêm

[CCNAv6 S2] 8.3.1.2 Packet Tracer - Skills Integration Challenge

Hình ảnh
Packet Tracer – Skills Integration Challenge Addressing Table VLAN Port Assignments and DHCP Information Scenario In this culminating activity, you will configure VLANs, trunks, DHCP Server, DHCP relay agents, and configure a router as a DHCP client. Requirements Using the information in the tables above, implement the following requirements: ·         Create VLANs on S2 and assign VLANs to appropriate ports. Names are case-sensitive ·         Configure S2 ports for trunking. ·         Configure all non-trunk ports on S2 as access ports. ·         Configure R1 to route between VLANs. Subinterface names should match the VLAN number. ·         Configure R1 to act as a DHCP server for the VLANs attached to S2. -       Create a DHCP pool for each VLAN. Names are case-sensitive. -       Assign the ap...
Đọc thêm

[CCNAv6 S3] 7.2.3.5 Packet Tracer - Troubleshooting EIGRP for IPv4

Hình ảnh
Packet Tracer – Troubleshooting EIGRP for IPv4 Addressing Table Scenario In this activity, you will troubleshoot EIGRP neighbor issues. Use show commands to identify errors in the network configuration. Then, you will document the errors you discover and implement an appropriate solution. Finally, you will verify full end-to-end connectivity is restored. Troubleshooting Process 1.     Use testing commands to discover connectivity problems in the network and document the problem in the Documentation Table. 2.     Use verification commands to discover the source of the problem and devise an appropriate solution to implement. Document the proposed solution in the Documentation Table. 3.     Implement each solution one at a time and verify if the problem is resolved. Indicate the resolution status in the Documentation Table. 4.     If the problem is not resolved, it may be necessary to first remove the implemented solution befor...
Đọc thêm