[CCNAv6 S2] 2.2.4.4 Packet Tracer - Configuring IPv6 Static and Default Routes



Packet Tracer - Configuring IPv6 Static and Default Routes
IPv6 Addressing Table

Objectives

Part 1: Examine the Network and Evaluate the Need for Static Routing

Part 2: Configure IPv6 Static and Default Routes

Part 3: Verify Connectivity

Background

In this activity, you will configure IPv6 static and default routes. A static route is a route that is entered manually by the network administrator in order to create a route that is reliable and safe. There are four different static routes used in this activity: a recursive static route; a directly attached static route; a fully specified static route; and a default route.

Part 1:     Examine the Network and Evaluate the Need for Static Routing
a.     Looking at the topology diagram, how many networks are there in total?

b.    How many networks are directly connected to R1, R2, and R3?

c.     How many static routes are required by each router to reach networks that are not directly connected?

d.    Which command is used to configure IPv6 static routes?

Part 2:     Configure IPv6 Static and Default Routes
Step 1:     Enable IPv6 routing on all routers.

Before configuring static routes, we must configure the router to forward IPv6 packets
Which command accomplishes this?
Enter this command on each router.
Step 2:     Configure recursive static routes on R1.

Configure an IPv6 recursive static route to every network not directly connected to R1.
Step 3:     Configure a directly attached and a fully specified static route on R2.

a.     Configure a directly attached static route from R2 to the R1 LAN.

b.    Configure a fully specific route from R2 to the R3 LAN.
Note: Packet Tracer v6.0.1 only checks for directly attached and recursive static routes. Your instructor may ask to review your configuration of a fully specified IPv6 static route.

Step 4:     Configure a default route on R3.

Configure a recursive default route on R3 to reach all networks not directly connected.
Step 5:     Verify static route configurations.

a.     Which command is used in Packet Tracer to verify the IPv6 configuration of a PC from the command prompt?

b.    Which command displays the IPv6 addresses configured on a router's interface?

c.     Which command displays the contents of the IPv6 routing table?

Part 3:     Verify Network Connectivity
Every device should now be able to ping every other device. If not, review your static and default route configurations.


Configuration R1:

enable
configure terminal
ipv6 route 2001:DB8:1:2::/64 2001:DB8:1:A001::2
ipv6 route 2001:DB8:1:A002::/64 2001:DB8:1:A001::2
ipv6 route 2001:DB8:1:3::/64 2001:DB8:1:A001::2

Configuration R2:

enable
configure terminal
ipv6 route 2001:DB8:1:1::/64 Serial0/0/0
ipv6 route 2001:DB8:1:3::/64 Serial0/0/1


Configuration R3:

enable
configure terminal
ipv6 route ::/0 2001:DB8:1:A002::1





Nhận xét

Đăng nhận xét

Bài đăng phổ biến từ blog này

[CCNAv6 S4] 8.2.4.14 Packet Tracer - Troubleshooting Enterprise Networks 3

Hình ảnh
Packet Tracer – Troubleshooting Enterprise Networks 3 Addressing Table Background This activity uses a variety of technologies you have encountered during your CCNA studies, including routing, port security, EtherChannel, DHCP, NAT, PPP, and Frame Relay. Your task is to review the requirements, isolate and resolve any issues, and then document the steps you took to verify the requirements. Note: This activity begins with a partial score. Requirements DHCP ·         R1 is the DHCP server for the R1 LAN. Switching Technologies ·         Port security is configured to only allow PC1 to access S1's F0/3 interface. All violations should disable the interface. ·         Link aggregation using EtherChannel is configured on S2, S3, and S4. Routing ·         All routers are configured with OSPF process ID 1 and no routing updates should be sent across interfaces that do n...
Đọc thêm

[CCNAv6 S2] 2.2.2.4 Packet Tracer - Configuring IPv4 Static and Default Routes

Hình ảnh
Packet Tracer - Configuring IPv4 Static and Default Routes Addressing Table Objectives Part 1: Examine the Network and Evaluate the Need for Static Routing Part 2: Configure Static and Default Routes Part 3: Verify Connectivity Background In this activity, you will configure static and default routes. A static route is a route that is entered manually by the network administrator to create a reliable and safe route. There are four different static routes that are used in this activity: a recursive static route, a directly attached static route, a fully specified static route, and a default route. Part 1:     Examine the Network and Evaluate the Need for Static Routing a.     Looking at the topology diagram, how many networks are there in total? b.    How many networks are directly connected to R1, R2, and R3? c.     How many static routes are required by each router to reach networks that are not directly ...
Đọc thêm

[CCNAv6 S2] 7.3.2.4 Packet Tracer - Troubleshooting Standard IPv4 ACLs

Hình ảnh
Packet Tracer – Troubleshooting Standard IPv4 ACLs Addressing Table Objectives Part 1: Troubleshoot ACL Issue 1 Part 2: Troubleshoot ACL Issue 2 Part 3: Troubleshoot ACL Issue 3 Scenario This network is meant to have the following three policies implemented: ·         Hosts from the 192.168.0.0/24 network are unable to access network 10.0.0.0/8. ·         L3 can’t access any devices in network 192.168.0.0/24. ·         L3 can’t access Server1 or Server2. L3 should only access Server3. ·         Hosts from the 172.16.0.0/16 network have full access to Server1, Server2 and Server3. Note: All FTP usernames and passwords are “cisco”. No other restrictions should be in place. Unfortunately, the rules that have been implemented are not working correctly. Your task is to find and fix the errors related to the access lists on R1. Part 1:     Troublesh...
Đọc thêm