[CCNAv6 S4] 2.5.1.2 Packet Tracer - Skills Integration Challenge



Packet Tracer – Skills Integration Challenge
Addressing Table

Background

This activity allows you to practice a variety of skills including configuring VLANs, PPP with CHAP, static and default routing, using IPv4 and IPv6. Due to the sheer number of graded elements, you can click Check Results and Assessment Items to see if you correctly entered a graded command. Use the cisco and class passwords to access privileged EXEC modes of the CLI for routers and switches.

Requirements

Addressing

·         The addressing scheme uses the 192.168.1.0/24 address space. Additional address space is available between VLAN 15 and VLAN 1. VLAN 25 needs enough addresses for 50 hosts. Determine the subnet and complete the subnet table below.


·         Complete the Addressing Table by assigning the following addresses to VLAN 25:
o    R2 G0/0.25 - First IPv4 address
o    PC25 - 2nd IPv4 address
o    L25 - Last IPv4 address
·         Configure IPv4 addressing on the necessary end devices.
·         On R2, create and apply IPv4 and IPv6 addressing to the G0/0.25 subinterface.
VLANs

·         On S1, create VLAN 86 and name it BlackHole.
·         Configure S1 ports in static mode with the following requirements:
o    F0/1 is the native trunk for VLAN 99.
o    F0/7 - F0/18 as access ports in VLAN 15.
o    F0/19 - F0/24 as access ports in VLAN 25.
o    G0/1 - 2 and F0/2 - F0/6 are unused. They should be properly secured and assigned to the BlackHole VLAN.
·         On R2, configure inter-VLAN routing. VLAN 99 is the native VLAN.
PPP

·         Configure R1 and R2 to use PPP with CHAP for the shared link. The password for CHAP is cisco.
Routing

·         On R1, configure IPv4 and IPv6 default routes using the appropriate exit interface.
·         On R2, configure an IPv6 default route using the appropriate exit interface.
·         Configure IPv4 OSPF using the following requirements:
o    Use process ID 1.
o    Routers R1 and R2 are in area 0.
o    R1 uses router ID 1.1.1.1.
o    R2 uses router ID 2.2.2.2.
o    Advertise specific subnets.
o    On R1, propagate the IPv4 default route created.
·         Configure IPv6 OSPF using the following requirements:
o    Use process ID 1.
o    Routers R1 and R2 are in area 0.
o    Configure OSPF on appropriate interfaces on R1 and R2.
o    R1 uses router ID 1.1.1.1.
o    R2 uses router ID 2.2.2.2.
Connectivity

·         All devices should be able to ping the web server.




Configuration R2:

enable
configure terminal
interface g0/0
 no shutdown
interface g0/0.1
 encapsulation dot1q 1
 ip address 192.168.1.193 255.255.255.224
interface g0/0.15
 encapsulation dot1q 15
 ip address 192.168.1.1 255.255.255.128
interface g0/0.25
 encapsulation dot1q 25
 ip address 192.168.1.129 255.255.255.192
 ipv6 address FE80::2 link-local
 ipv6 address 2001:DB8:A:25::1/64
interface g0/0.99
 encapsulation dot1q 99 native
 ip address 192.168.1.225 255.255.255.224
 exit
username R1 password cisco
interface s0/0/0
 encapsulation ppp
 ppp authentication chap
 exit
ipv6 route ::/0 s0/0/0
ipv6 unicast-routing
router ospf 1
 router-id 2.2.2.2
 log-adjacency-changes
 network 10.1.1.0 0.0.0.3 area 0
 network 192.168.1.0 0.0.0.127 area 0
 network 192.168.1.128 0.0.0.63 area 0
 network 192.168.1.192 0.0.0.31 area 0
 network 192.168.1.224 0.0.0.31 area 0
ipv6 router ospf 1
 router-id 2.2.2.2
 log-adjacency-changes
!
interface Serial0/0/0
 ipv6 ospf 1 area 0
interface GigabitEthernet0/0.1
 ipv6 ospf 1 area 0
interface GigabitEthernet0/0.15
 ipv6 ospf 1 area 0
interface GigabitEthernet0/0.25
 ipv6 ospf 1 area 0
interface GigabitEthernet0/0.99
 ipv6 ospf 1 area 0
 end
write memory
!


Configuration S1:

enable
configure terminal
vlan 86
 name BlackHole
 exit
interface f0/1
 switchport mode trunk
 switchport trunk native vlan 99
interface range f0/7-18
 switchport mode access
 switchport access vlan 15
interface range f0/19-24
 switchport mode access
 switchport access vlan 25
interface range f0/2-6,g0/1-2
 switchport mode access
 switchport access vlan 86
 shutdown
 exit
ip default-gateway 192.168.1.225
end
write memory
!


Configuration R1:

enable
configure terminal
interface s0/0/0
 encapsulation ppp
 ppp authentication chap
 exit
username R2 password cisco
ipv6 route ::/0 s0/0/1
ip route 0.0.0.0 0.0.0.0 s0/0/1
ipv6 unicast-routing
!
router ospf 1
 router-id 1.1.1.1
 log-adjacency-changes
 network 10.1.1.0 0.0.0.3 area 0
 default-information originate
!
ipv6 router ospf 1
 router-id 1.1.1.1
 log-adjacency-changes
!
interface Serial0/0/0
 ipv6 ospf 1 area 0
 end
write memory
!

END !~!





Nhận xét

Đăng nhận xét

Bài đăng phổ biến từ blog này

[CCNAv6 S4] 8.2.4.14 Packet Tracer - Troubleshooting Enterprise Networks 3

Hình ảnh
Packet Tracer – Troubleshooting Enterprise Networks 3 Addressing Table Background This activity uses a variety of technologies you have encountered during your CCNA studies, including routing, port security, EtherChannel, DHCP, NAT, PPP, and Frame Relay. Your task is to review the requirements, isolate and resolve any issues, and then document the steps you took to verify the requirements. Note: This activity begins with a partial score. Requirements DHCP ·         R1 is the DHCP server for the R1 LAN. Switching Technologies ·         Port security is configured to only allow PC1 to access S1's F0/3 interface. All violations should disable the interface. ·         Link aggregation using EtherChannel is configured on S2, S3, and S4. Routing ·         All routers are configured with OSPF process ID 1 and no routing updates should be sent across interfaces that do n...
Đọc thêm

[CCNAv6 S2] 2.2.2.4 Packet Tracer - Configuring IPv4 Static and Default Routes

Hình ảnh
Packet Tracer - Configuring IPv4 Static and Default Routes Addressing Table Objectives Part 1: Examine the Network and Evaluate the Need for Static Routing Part 2: Configure Static and Default Routes Part 3: Verify Connectivity Background In this activity, you will configure static and default routes. A static route is a route that is entered manually by the network administrator to create a reliable and safe route. There are four different static routes that are used in this activity: a recursive static route, a directly attached static route, a fully specified static route, and a default route. Part 1:     Examine the Network and Evaluate the Need for Static Routing a.     Looking at the topology diagram, how many networks are there in total? b.    How many networks are directly connected to R1, R2, and R3? c.     How many static routes are required by each router to reach networks that are not directly ...
Đọc thêm

[CCNAv6 S2] 7.3.2.4 Packet Tracer - Troubleshooting Standard IPv4 ACLs

Hình ảnh
Packet Tracer – Troubleshooting Standard IPv4 ACLs Addressing Table Objectives Part 1: Troubleshoot ACL Issue 1 Part 2: Troubleshoot ACL Issue 2 Part 3: Troubleshoot ACL Issue 3 Scenario This network is meant to have the following three policies implemented: ·         Hosts from the 192.168.0.0/24 network are unable to access network 10.0.0.0/8. ·         L3 can’t access any devices in network 192.168.0.0/24. ·         L3 can’t access Server1 or Server2. L3 should only access Server3. ·         Hosts from the 172.16.0.0/16 network have full access to Server1, Server2 and Server3. Note: All FTP usernames and passwords are “cisco”. No other restrictions should be in place. Unfortunately, the rules that have been implemented are not working correctly. Your task is to find and fix the errors related to the access lists on R1. Part 1:     Troublesh...
Đọc thêm