[CCNAv6 S3] 8.3.3.5 Packet Tracer - Configuring Basic OSPFv3 in a Single Area



Packet Tracer – Configuring Basic OSPFv3 in a Single Area
Addressing Table

Objectives

Part 1: Configure OSPFv3 Routing

Part 2: Verify Connectivity

Background

In this activity, the IPv6 addressing is already configured. You are responsible for configuring the three router topology with basic single area OSPFv3 and then verifying connectivity between end devices.

Part 1:     Configure OSPFv3 Routing
Step 1:     Configure OSPFv3 on R1, R2 and R3.

Use the following requirements to configure OSPF routing on all three routers:

-       Enable IPv6 routing
-       Process ID 10
-       Router ID for each router: R1 = 1.1.1.1; R2 = 2.2.2.2; R3 = 3.3.3.3
-       Enable OSPFv3 on each interface
Note: Packet Trace version 6.0.1 does not support the auto-cost reference-bandwidth command, so you will not be adjust bandwidth costs in this activity.

Step 2:     Verify OSPF routing is operational.

Verify each router has established adjacency with the other two routers. Verify the routing table has a route to every network in the topology.

Part 2:     Verify Connectivity
Each PC should be able to ping the other two PCs. If not, check your configurations.

Note: This activity is graded using only connectivity tests. The instructions window will not show your score. To see your score, click Check Results > Assessment Items. To see the results of a specific connectivity test, click Check Results > Connectivity Tests.




 Configuration R1:

enable
configure terminal
!
ipv6 unicast-routing
!
ipv6 router ospf 10
 router-id 1.1.1.1
 exit
!
interface GigabitEthernet0/0
 ipv6 ospf 10 area 0
interface Serial0/0/0
 ipv6 ospf 10 area 0
interface Serial0/0/1
 ipv6 ospf 10 area 0
!
 end
write memory
!


Configuration R2:

enable
configure terminal
!
ipv6 unicast-routing
!
ipv6 router ospf 10
 router-id 1.1.1.1
 exit
!
interface GigabitEthernet0/0
 ipv6 ospf 10 area 0
interface Serial0/0/0
 ipv6 ospf 10 area 0
interface Serial0/0/1
 ipv6 ospf 10 area 0
!
 end
write memory
!

Configuration R3:

enable
configure terminal
!
ipv6 unicast-routing
!
ipv6 router ospf 10
 router-id 3.3.3.3
 exit
!
interface GigabitEthernet0/0
 ipv6 ospf 10 area 0
interface Serial0/0/0
 ipv6 ospf 10 area 0
interface Serial0/0/1
 ipv6 ospf 10 area 0
!
!
 end
write memory
!

END !~!


Nhận xét

Đăng nhận xét

Bài đăng phổ biến từ blog này

[CCNAv6 S4] 8.2.4.14 Packet Tracer - Troubleshooting Enterprise Networks 3

Hình ảnh
Packet Tracer – Troubleshooting Enterprise Networks 3 Addressing Table Background This activity uses a variety of technologies you have encountered during your CCNA studies, including routing, port security, EtherChannel, DHCP, NAT, PPP, and Frame Relay. Your task is to review the requirements, isolate and resolve any issues, and then document the steps you took to verify the requirements. Note: This activity begins with a partial score. Requirements DHCP ·         R1 is the DHCP server for the R1 LAN. Switching Technologies ·         Port security is configured to only allow PC1 to access S1's F0/3 interface. All violations should disable the interface. ·         Link aggregation using EtherChannel is configured on S2, S3, and S4. Routing ·         All routers are configured with OSPF process ID 1 and no routing updates should be sent across interfaces that do n...
Đọc thêm

[CCNAv6 S2] 2.2.2.4 Packet Tracer - Configuring IPv4 Static and Default Routes

Hình ảnh
Packet Tracer - Configuring IPv4 Static and Default Routes Addressing Table Objectives Part 1: Examine the Network and Evaluate the Need for Static Routing Part 2: Configure Static and Default Routes Part 3: Verify Connectivity Background In this activity, you will configure static and default routes. A static route is a route that is entered manually by the network administrator to create a reliable and safe route. There are four different static routes that are used in this activity: a recursive static route, a directly attached static route, a fully specified static route, and a default route. Part 1:     Examine the Network and Evaluate the Need for Static Routing a.     Looking at the topology diagram, how many networks are there in total? b.    How many networks are directly connected to R1, R2, and R3? c.     How many static routes are required by each router to reach networks that are not directly ...
Đọc thêm

[CCNAv6 S2] 7.3.2.4 Packet Tracer - Troubleshooting Standard IPv4 ACLs

Hình ảnh
Packet Tracer – Troubleshooting Standard IPv4 ACLs Addressing Table Objectives Part 1: Troubleshoot ACL Issue 1 Part 2: Troubleshoot ACL Issue 2 Part 3: Troubleshoot ACL Issue 3 Scenario This network is meant to have the following three policies implemented: ·         Hosts from the 192.168.0.0/24 network are unable to access network 10.0.0.0/8. ·         L3 can’t access any devices in network 192.168.0.0/24. ·         L3 can’t access Server1 or Server2. L3 should only access Server3. ·         Hosts from the 172.16.0.0/16 network have full access to Server1, Server2 and Server3. Note: All FTP usernames and passwords are “cisco”. No other restrictions should be in place. Unfortunately, the rules that have been implemented are not working correctly. Your task is to find and fix the errors related to the access lists on R1. Part 1:     Troublesh...
Đọc thêm